Use a V-groove stake when the race face has room for a groove. Use a threaded retainer where staking is hard to reach, and a bolted plate when you need the most holding power and can spare the space. Use a housing stake only when a groove is not possible, and treat snap rings and retaining compound as last resorts. Whichever method you pick, the housing has to be made for it, and the staking force is set by a trial and a proof test, not by a table alone.
| Method | Effect on internal clearance | Effect on housing stress | Added space and weight | Retention capability | Housing damaged on replacement |
|---|---|---|---|---|---|
| V-groove stake | None | None | None | Medium | No |
| Threaded retainer | None | None | None | Medium | No |
| Bolted plate | None | None | High | High | No |
| Housing stake | High | High | None | Low | Yes |
The table comes from a bearing maker's retention reference, called the inch reference below because its figures are in inches. A second page from the same maker group gives metric figures and is called the metric page. The inch reference lists adhesive bonding, snap rings and threaded cover plates as methods to use only as a last resort. This article calls the two staking methods by the names these references use. A V-groove stake flares a lip of the bearing's outer race over the housing chamfer. A housing stake presses housing metal over the race chamfer.
Which Retention Method Fits Which Housing
Use a V-groove stake when the race face has room for a groove. The inch reference calls it the most widely used and recommended method. The outer race carries a small groove on each face, which leaves a lip at the outer corners. A staking tool flares those lips over the chamfered edges of the housing. The inch reference's table shows no added space or weight, no effect on internal clearance and no effect on housing stress.
Replaceability rules out only one method. A V-groove stake, a threaded retainer and a bolted plate all let the bearing be replaced without damaging the housing, and the inch reference gives no limit on the number of replacements. A housing stake does damage the housing, so the housing goes out with the bearing.
The inch reference rates the retention capability as medium for a V-groove stake and a threaded retainer, high for a bolted plate and low for a housing stake. Bolted plates give the most holding power and cost the most space and weight.
V-Groove Staking: What the Race and Housing Need
Three conditions must hold before a V-groove stake is possible. The maker states them as a list:
- Race hardness of Rc 40 maximum.
- Enough room on the race face to machine the groove.
- A groove size that can carry the axial load.
The housing needs a chamfer of the right size, the staking tools must match the groove size, and a hydraulic or pneumatic press must be able to apply the force. None of these sources discusses stainless steel races, so check the hardness of the actual race material and condition against the data sheet before choosing this method. If the race is harder than the limit, a V-groove stake is not an option and the other methods in the table apply.
The housing width matters too. A distributor's staking guide suggests making the housing as wide as the outer race. The bearing then sits flush, centres more easily and the lip conforms to the chamfer better. The inch reference also sets a housing width tolerance of .005 in (about 0.13 mm) for staking.
Chamfer Size for V-Groove Staking
The housing chamfer diameter is the bore plus the width difference plus twice the groove depth. The inch reference's formula is C = M + [T - H + (2 x E)], with a tolerance of +.008 / -.007 in. M is the bore or bearing outside diameter, T is the housing width, H is the outer race width and E is the average groove depth for the groove size.
| V-groove size | Average groove depth E (in) | E (mm, converted) |
|---|---|---|
| A | .023 | 0.58 |
| B | .033 | 0.84 |
| C | .053 | 1.35 |
| D | .073 | 1.85 |
Worked example. A 1.500 in (38.1 mm) bearing with a B groove, in a housing as wide as the race (T = H). The chamfer diameter is 1.500 + 0 + 2 x 0.033 = 1.566 in, which is about 39.78 mm. The tolerance of +.008 / -.007 in then applies. For another groove letter, swap in its depth from the table.
Staking Force and Proof Testing
Treat any published staking force as a starting point. The real force is set by a trial assembly and checked by a proof test. The inch reference's procedure says a trial assembly should be made for each new bearing lot to find the force that meets the required axial retention. Excessive force can distort the bearing and impair its function and life.
The inch tables give the force as the bearing outside diameter times a constant for the groove size. The constants hold for an outer race with an ultimate tensile strength of 140,000 psi and scale in proportion to the strength of other materials.
| V-groove size | Constant (lbf per inch of outside diameter) |
|---|---|
| A | 7,700 |
| B | 12,000 |
| C | 17,700 |
| D | 25,800 |
Worked example. A 1.500 in bearing with a B groove needs 1.500 x 12,000 = 18,000 lbf, which is about 80 kN.
A metric page from the same maker group gives different numbers. For a steel race of 30 to 35 HRC and a B groove, it lists a staking load of 3138 x D newtons, with D the bearing outside diameter in mm. For the same 38.1 mm bearing that is about 120 kN, roughly one and a half times the inch figure. The metric page states no race strength, so the two are not like for like. The ratio also changes with the groove letter: it is about 2 for groove A. The inch reference tells you to find the force by trial assembly. The metric page tells you to adjust it to the staking appearance and the axial proof load. Neither number can be used without checking.
The procedure after the trial is short. Stake with the force found, turn the assembly and apply it again. The inch reference turns the assembly 90 degrees. The distributor guide describes a turn and a second stake, or three stakes per side as best practice, so follow the tool maker's instruction for your tooling. As a minimum, proof-test the first and last article staked. The staking tools are tool steel, hardened to Rc 55 to 60, with 45 to 50 degree outside angles for most jobs. A secondary tool of 60 to 70 degrees can reduce the gap between the housing chamfer and the race lip.
A slight gap may remain between the race lip and the chamfer after staking. The inch reference says this gap should not be a cause for rejection if the bearing meets the specified thrust load. The metric page puts the limit at 0.15 mm, below which the axial load capacity is not affected.
When V-Groove Staking Is Not Possible
If the race face has no room for a groove, or the race material is not ductile, use another method. The inch reference allows a housing stake only in those two cases. Its main drawback is race contraction, which adversely affects the internal fit-up. The table above shows a high effect on clearance and on housing stress, low retention and a damaged housing on replacement. The metric page adds that the housing has to be replaced together with the bearing. It also notes that body staking can raise axial load strength, but that torque and clearance are easily affected, while the inch reference rates a housing stake low for retention.
The inch reference recommends a threaded retainer where the bearing must be replaced easily and where access for conventional staking is difficult. It adds no space and has no clearance effect. A bolted plate gives the highest retention and allows unlimited replacements without housing damage, at the cost of space and weight. The inch reference's text praises the axial thrust capability of a threaded retainer, while its table rates the retention as medium. This article uses the table. The metric page also lists roller staking and circumferential-line staking, which need simpler tooling than a press.
Adhesive and Snap Rings as Last Resorts
A retaining compound makes the adhesive layer carry the axial load in shear. A racing-team article puts it this way: the shear strength of the adhesive can often be the weakest link in the system. When the bearing sees an axial load, the compound can fail in shear. As it cures it expands and can put a radial preload on the bearing, which causes stiction. If any compound gets inside the joint, the bearing is useless.
A racing-team article describes a housing with a flange at one end and a retaining ring at the other, which allows the bearing to be removed and replaced. It needs a housing wider than the ball, so removable misalignment washers or top hats are needed. The inch reference ranks snap rings below the four methods in the table but gives no reason. Confirm the ring and its groove with the bearing maker before choosing this route.
Fit, Axial Load and Retention
The fit locates the ring in the bore, and the retention method holds it against axial load. The inch reference's housing guidance is a bearing-to-housing fit from .0002 in tight to .0008 in loose (about 0.005 mm tight to 0.020 mm loose) and a bore finish of 32 Ra. The metric page gives a transition fit, -0.013 mm tight to +0.013 mm loose. Our guide on press fit and slip fit covers the choice of fit in detail.
Heavy interference is not generally recommended, because it reduces internal clearance. The inch reference says the race can contract by up to 100% of the interference fit, so allow for that in the ball-to-race fit-up. If a heavy fit is needed, assemble with a temperature difference to avoid galling. After assembly the bearing usually cannot be replaced, because of galling on pushout. A racing-team article adds that a bearing in a bore that is too small carries a constant radial load, and that a welded housing should be reamed to final size after welding.
Press the bearing in by the outer race only. The metric page says the ball should never be pressed, and the inch reference says no hammer or shock-inducing impact should be used. Our article on a bearing spinning in the housing covers what to check when the ring turns in the bore.
Check the bearing's own axial rating as well as the retention method. A racing-team article on chrome-plated, PTFE-lined rod ends notes that the ultimate axial load is often only 5 to 10% of the ultimate radial load. Check the rating of your own bearing. See how to choose for radial and axial load.
Housing Material and Corrosion
A 300-series or 17-4PH bearing needs no surface treatment against titanium, corrosion resistant steel or superalloy housings, but the inch reference's galvanic table calls for treatment against aluminium and low-alloy steel. The table gives these results by housing material:
| Housing material | Table result for a 300-series or 17-4PH bearing |
|---|---|
| Aluminium alloy | Treatment called for (codes A and C: anodize or Alodine, and cadmium plate) |
| Low-alloy steel | Treatment called for (code C, cadmium plate) |
| Titanium, corrosion resistant steel, superalloy | Satisfactory with no surface treatment |
We would confirm any treatment against your drawing and the environment, and we do not specify plating here. The sources do not cover staking into aluminium or stainless housings. The distributor's staking guide covers steel housings only and does not say whether that includes stainless steel. Check the staking force and the groove with the bearing maker when the housing is aluminium or stainless steel.
What to Send for a Retention Quote
Profab Machine makes stainless steel spherical bearings in 304, 316L and 17-4PH to your drawing. We confirm the retention method against the housing drawing before we quote. Send:
- The housing drawing with bore, width and chamfer
- Bearing size and the grade you need (304, 316L, 17-4PH)
- The size and direction of the axial load
- Whether the bearing must be replaceable in the same housing
- The housing material and the working environment
- Quantity per order
Conclusion
A V-groove stake suits a bearing whose race hardness and face width allow the groove. A threaded retainer suits places where staking is hard to reach, and a bolted plate suits the highest holding power. A housing stake, a snap ring or a retaining compound is the exception. Calculate the chamfer from the groove depth, take the staking force as a starting point, then settle it by trial assembly and a proof test. If you have a housing drawing, send the list above to Profab Machine and we will confirm the method with you. Our spherical bearing guide places retention among the other housing and fit choices.

