Get A Quote
Complete Spherical Bearing Guide

Spherical Bearing Guide: Types, Materials, Sizes, Selection

A practical guide to stainless steel spherical plain bearings: radial, angular contact and axial types, the COM, GEC, SLB, WPB and YPB series, sliding systems, materials, sizes, tilt angle and selection.

Engineering GuideSpherical Plain BearingsStainless Steel

Quick Answer: choose a spherical plain bearing by working through five decisions in order. First pick the type from the load direction and the sliding system from the maintenance access. Then set the size and tilt angle from the envelope and the motion, the ring material from the environment, and last the housing fit. A bearing that is right on the first four can still fail in a loose or out-of-round bore.

DecisionOptionsStarting point
TypeRadial, angular contact, axialRadial for almost every linkage, because the load acts across the pin
Sliding systemPTFE-lined, metal-to-metal, molded racePTFE-lined where the joint cannot be greased, metal-to-metal for heavy or shock load
Size and angleBore, outside diameter, width, tiltFit the housing envelope, then check the tilt against the measured installed angle
Ring materialPlated bearing steel, 304, 316, 17-4PH316 where salt or washdown reaches the joint, 17-4PH where load governs (Profab offers 17-4PH on COM, COM-T, GEC and YPB, and 304 or 316 on SLB and WPB)
Housing fitPress fit, slip fit, staked or retainedHold the bore round and to tolerance so the outer ring cannot turn

What Is a Spherical Plain Bearing?

A spherical plain bearing is a bearing with an inner ring shaped like part of a ball and an outer ring with a matching hollow. The two surfaces slide on each other, so the inner ring, and the pin through it, can tilt and turn inside the outer ring while the bearing carries load.

It is a separate bearing element that goes into a housing, cup or clevis eye of your own, which sets it apart from a rod end and from a ball joint. A rod end builds the same kind of bearing into a threaded body, and a ball joint uses a ball stud held in a socket. It is also not a spherical roller bearing, which rolls instead of sliding and belongs to a different speed and load range.

How a Spherical Bearing Works

The curved sliding surface lets the inner ring swivel to an angle without binding, so a pin that is slightly out of line with the housing still sits flat on the bearing. This is why the bearing is used where parts tilt as they move or where two mounting points cannot be machined perfectly in line.

The motion is slow oscillation or slow rotation under load, and the sliding layer is what wears. The catalogue calls the largest angle the tilt or misalignment angle, and it is a geometric limit: past it the inner ring edge meets the outer ring and the contact moves onto the edge.

Radial, Angular Contact and Axial Types

Spherical plain bearings are grouped by the direction of the load they are built for. Radial bearings follow ISO 12240-1, and the angular contact and axial types have their own parts of ISO 12240. A radial bearing carries load across the pin. An angular contact bearing carries a heavy axial load in one direction along an inclined contact angle, and an axial bearing carries thrust along the shaft with only a small radial share.

Most linkages, cylinder eyes and pivots are radial. A radial bearing can take combined radial and axial load. A joint with a steady thrust component needs the axial rating and the combined-load method in the maker's catalogue checked before the type is chosen. Angular contact bearings are fitted in pairs when the thrust reverses.

Profab Series: COM, COM-T, GEC, SLB, WPB and YPB

Profab makes stainless spherical plain bearings in six series, which differ mainly in the sliding system and the angle. The table gives the use each series is chosen for.

SeriesDesignChosen for
COMMetal-to-metal with lubrication groove and holeGeneral radial load where the joint can be greased
COM-TPTFE-lined version of the COM platformDry, oscillating joints where access for greasing is limited
GECRadial, PTFE-lined raceCylinder eyes, heavy linkage pivots and articulated joints
SLBInjection-molded reinforced PTFE-nylon raceCompact, low-friction, lighter duty
WPBPTFE-lined, no routine greasingFood and packaging machinery, access panels, outdoor linkages
YPBWide inner ring for extra tiltSteering joints, suspension links and lift mechanisms

Start from the load direction and the maintenance access, because the bore is easier to change than the sliding system. The GEC series, for example, runs from 4 to 30 mm bore, with a catalogue tilt angle that falls from 16 degrees on the smallest size to 6 degrees on the largest. Across the other series the catalogue tilt is typically about 6 to 15 degrees for WPB, 8.5 to 10 for SLB and 18 to 24 for YPB. The angle tends to be lower on larger sizes but not in every step, so confirm the figure for the exact size.

Sliding Systems: PTFE-Lined, Metal-to-Metal and Molded

The sliding system sets the maintenance, the friction and the load the bearing can carry. A PTFE-lined bearing lays down a thin film of PTFE on the ball during use, so it needs no grease and tolerates slight geometric error. A metal-to-metal bearing slides steel on steel with grease, takes heavier and shock loads, and is relubricated through its grease holes.

A molded race of reinforced PTFE and nylon sits between the two for compact, lightly loaded joints. The practical question is whether anyone can reach the joint with a grease gun on schedule. Where nobody can, a liner is the safer choice. Where the load is heavy and the joint can be greased, metal-to-metal keeps its capacity.

Open and Sealed Bearings

An open bearing leaves the sliding surface exposed, so it can be inspected, cleaned and relubricated, while a sealed bearing adds a lip seal on each side to hold grease in and keep dirt out. A PTFE-lined bearing takes no grease, so its seal only has to keep contamination out.

Seals also cost angle. As the ball tilts toward its limit, the seal on one side can lift and let contamination in, so the practical angle of a sealed bearing can sit below the geometric maximum. The catalogue shows the figure for the exact part. Choose sealed for dust, mud and spray, and open where cleaning or relubrication is part of the routine.

Lubrication, Temperature and Liner Limits

A greased metal-to-metal bearing lives on its lubrication interval. When the interval is exceeded the grease film breaks down under load and heat, and a grease that is too stiff for the temperature will not spread across the contact until the joint warms up. After greasing, cycle the joint gently so the grease spreads before the machine works hard.

Seals and liners have temperature ceilings of their own. NBR lip seals typically work up to about 100 °C and FKM up to roughly 200 °C. Hot, strong caustic washdown can shorten the life of a liner depending on the liner system, so confirm the limit with the liner maker. Every self-lubricating liner also has a pV limit, the product of contact pressure and sliding speed. Running above it heats the liner faster than it can lose the heat.

Spherical Bearing Materials in Common Use

The inner ring, the outer ring and the liner are separate material choices. The common inner rings are chrome-plated bearing steel for dry indoor machines, and stainless steel where water, washdown or salt reaches the joint. The liner is usually a PTFE fabric or sintered layer, a molded PTFE-nylon, or none in the metal-to-metal case.

MaterialWhere it is usedWatch for
Chrome-plated bearing steel (general catalogue practice; Profab supplies stainless)Dry, indoor and high-load machineryPlating wears through and the steel then rusts when wet
304 stainless steelIndoor, food-adjacent and mild environmentsPits sooner than 316 where chlorides are present
316 and 316L stainless steelMarine, outdoor and chemical-cleaned equipmentSofter than plated steel, so the rating must be checked for the stainless ring
17-4PH stainless steelHigh-load and high-cycle joints that still need corrosion resistanceChloride resistance close to 304, so keep it for load-driven joints
PTFE liner or molded raceJoints that cannot be greasedLimits on load, speed and temperature, which the liner sets and not the ring

Swapping a plated steel bearing for a stainless one for corrosion reasons also changes its rating, since a stainless ring is usually softer than a hardened plated ring. The ring grade and the load it allows are compared in the guide linked below.

Bore, Outside Diameter and Width

The size is set by the pin and by the housing space. The bore is the inner ring hole for the pin or bolt, and the outside diameter is the housing bore. The widths of the inner and outer rings set how the bearing sits between the clevis faces. The tilt angle is tied to those proportions, which is why a wide inner ring gives more angle.

Selected metric sizes from the Profab range:

Bore (mm)Outside diameter (mm)
614 or 18
816 or 22
1019 or 26
1222 or 30
2035 or 46
3047 or 66

Inch sizes are listed on the stainless steel spherical bearing page, and sizes outside the range are made to drawing. Profab confirms dimensions and angles at quotation and does not publish load ratings, because the rating depends on the ring material and the liner. A GEC size 20 bearing, for instance, is 35 mm outside diameter with a 16 mm inner ring, a 12 mm outer ring and a 9 degree tilt.

Standards and Bearing Designations

Radial spherical plain bearings follow the ISO 12240-1 dimension series, which is why bearings of the same series from different makers usually share the bore, outside diameter and width. In that system the GE designation typically means an open radial bearing, and the S in a suffix such as ES marks a lubrication groove with holes in the rings. A seal suffix such as 2RS marks the sealed versions, depending on the maker. GEH marks a wider inner ring and a larger outside diameter, and the seal is a separate suffix.

The envelope interchanges, but the tolerances, clearance grade, ratings, liner and ring material do not, so a replacement needs those checked as well as the bore and outside diameter. Profab’s GEC series is a metric radial series with a PTFE-lined race, and the other series are made to the same kind of envelope or to drawing.

Tilt Angle and Misalignment

The catalogue tilt angle is a limit and not a target. Standard series generally allow roughly 5 to 16 degrees depending on size and series, and wide-inner-ring and high-misalignment designs allow still more. Measure the angle on the assembled joint at its extremes, including the deflection under load, and leave a margin before comparing it with the catalogue figure.

Past the limit the contact moves to the ring edge, and the pressure there rises well above the nominal figure. Align the mount with the linkage where the design allows, because a mount that forces the joint near its limit wastes the angle before the motion starts. On a link with a rod end at each end, set both at mid-travel so that neither is pushed against its mount when the jam nut is tightened. If the measured angle will not fit inside a standard bearing, use a wide inner ring series or a misalignment spacer. A misalignment spacer is narrower where it meets the ring, so the ball can tilt farther before the hardware stops it.

Load, Life and Contact Pressure

Catalogues size a bearing on an equivalent radial load, found by adding the axial load times a catalogue factor to the radial load. The contact pressure from that load is then checked against a limit set by the liner and by how the load behaves: steady in one direction, alternating, or pulsing.

The pressure check and the life check are separate, so a joint can pass one and fail the other. The factors and ratings must come from the same catalogue, so the method here is a way to screen a design and not a rating for any Profab part.

Housing Fit and Installation

The outer ring is held in the housing by an interference fit or by staking or retaining, and the bore decides whether it stays put. A bore that is oversize, out of round or worn lets the outer ring turn, which scores the housing and wears the bearing. The fault is in the housing, although the bearing often gets the blame.

Retention is a separate choice from the press fit. Staking deforms a lip of the housing metal over the outer ring to hold it in place. A retaining ring or a retaining compound holds a bearing that is only lightly pressed, and the compound should be confirmed for stainless and passivated surfaces. A retaining ring can foul the ball at high misalignment, so check the ring ears against the tilt angle. The pin fit sets how the inner ring is held. Stainless on stainless can gall during a press fit, so use the assembly lubricant or anti-seize that the bearing maker specifies on the outer ring before pressing. Press the bearing in by the outer ring only, with a tool that does not load the sliding surface, and keep the bore clean and square. Where the housing is welded, bore it after welding so the heat does not leave it distorted.

Clearance Grades and Bore Tolerance

Spherical plain bearings come in normal, reduced (Group 2) and larger (Group 3) internal clearance grades. The larger grade is often chosen where a press fit will close up the clearance, and the fit in the housing decides which clearance the bearing actually has once installed. Pressing the outer ring in compresses it slightly and reduces the clearance. At the tight end of the interference range that can preload the bearing and raise the breakaway torque.

Check the residual clearance after installation against the maker’s data sheet. The reduced grade generally suits alternating loads with swivel motion where play must be kept low. A rattle at low load that disappears under higher load usually means too much internal clearance, such as the normal grade where the reduced grade was needed, or a loose bore. A knock on load reversal usually points to clearance that has grown from wear or to a loose seat.

Why Spherical Bearings Fail

Many failures trace to the joint and not to the bearing: a tilt beyond the limit, a loose bore, contamination in an open design, or a liner run past its load and speed. Corrosion and wear then show up as play, stiffness or noise, which are the signs that bring a joint in for replacement.

The signs differ by sliding system. A steel-on-steel bearing grinds as it wears, while a PTFE-lined bearing gives little warning until the liner wears through to the backing and the play opens up. Play together with heat at the housing, and a reddish-brown powder around the joint, points to fretting at the bore from too little interference. A rattle can mean the load is too light to hold the ball against one side of the contact zone.

Where Spherical Bearings Are Used

They sit in joints that carry load while tilting: hydraulic cylinder eyes, loader and lift linkages, steering and suspension links, hatch and access panel pivots, and filling and packaging machine arms. Marine equipment and food lines use stainless bearings for the same reason, because the joint is wet and has to resist rust.

Motorsport suspension is a useful case, because many A-arm tube ends use a pressed spherical bearing and not a threaded rod end. The choice there is a load-path decision, as the bearing sits in the structure and puts no shank in the load path.

Spherical Bearing, Rod End or Ball Joint

Use a separate spherical bearing when the structure itself can hold a compact bearing eye, and a rod end when the joint must adjust in length or be replaced as a unit. A ball joint suits a stud mounted in a socket at an angle. The rod end and the ball joint have their own guides, linked below.

The deciding difference is the load path. A threaded shank carrying a side load can fatigue in bending. Designs with a large bending load on the joint often use a pressed bearing, and rod ends where the length must adjust and the load runs along the shank. A rod end puts a threaded shank and body between the load and the bearing, while a pressed bearing carries the load straight into the housing. Where space is tight and the housing can be machined, the bearing is usually the more compact option.

Choosing a Profab Spherical Bearing

Profab machines spherical plain bearings in stainless steel in the six series above, in metal-to-metal and PTFE-lined forms, and to drawing for custom bore, width, liner and seal. Passivation and electropolishing are available for washdown and hygienic equipment.

Bearings can be supplied with the parts around them: misalignment spacers, rod ends and jam nuts in matching stainless, so the stack of bore, housing seat and bolt fits as one assembly. Tests such as material composition can be arranged on request through our production network.

What to Send for a Spherical Bearing Quote

A drawing or a worn part is the fastest route. Without one, the following lets us review the series, the liner and the ring material together before quoting.

  • Radial load and its direction, and whether it is steady, alternating or shock
  • Axial load, its direction and where it comes from
  • Oscillation angle and frequency, or the rotating speed
  • Bore, outside diameter and ring width, or the housing envelope
  • The installed misalignment angle, measured at its extremes
  • Environment: wet, salt, washdown, dust, temperature
  • Whether the joint can be greased, and the quantity

Conclusion

A spherical bearing choice comes down to a short sequence. The load sets the type, the maintenance access sets the sliding system, the envelope and the motion set the size and angle, the environment sets the ring material, and the housing fit comes last. A bearing of the right series can still fail early if the angle or the bore is wrong. Send the drawing, the load case and the environment, and Profab will check the series, the liner and the fit together.