Get A Quote
Complete Spacer Guide

Spacers Guide: Types, Materials, Sizes and How to Choose

A practical guide to stainless steel spacers and standoffs: round, hex, stepped and flanged types, bolt clearance bores, length tolerance stacks, materials in common use and selection.

Engineering GuideSpacers & StandoffsStainless Steel

Quick Answer: choose a spacer by working through five decisions in order. First pick the type, then the bore for the bolt, then the outside diameter and the end faces, then the length, and last the material. The tolerance on the length then decides whether a stack of parts still fits.

DecisionOptionsStarting point
TypePlain spacer, standoff, washer, shim, collarA plain spacer to hold a gap round a bolt, a standoff when the part must fasten without a through-bolt
BoreClearance for a bolt, or a threadThe clearance hole for the bolt size, or the thread of the fastener
Shape and facesRound, hex, stepped, flangedRound for most; hex where a spanner turns it; flanged where the load must spread
LengthSet by the stack, with a toleranceTake it from the assembly and tolerance it as tightly as the fit needs
MaterialPlated steel, stainless steel, aluminum, brass, nylonStainless where the part is wet, washed or exposed for years

What Is a Spacer?

A spacer is a hollow sleeve that holds two parts a set distance apart. It is usually round or hex with a center hole for a screw, bolt or stud, and it carries the clamping load of the fastener through its wall.

Several parts look like a spacer and do a different job. A standoff has threads and fastens directly, a bushing guides a moving shaft, and a washer spreads load. Ask whether the part must hold a distance, fasten, guide or spread, because the answer sets the fit, the finish and the tolerance.

How a Spacer Works

A spacer works by taking the place of air between two parts while a bolt clamps them together. The bolt supplies the clamping force, and the spacer is compressed between the parts, so its end faces must be flat and square to the bore for the load to spread evenly.

That is why length and end-face quality matter more than they look. A spacer that is a little short leaves a gap that can load or bend a flexible part, and one that is a little long stops the parts from seating. Both errors show up as stress in the assembly or as play in a bearing stack.

Spacer Types by Shape

Spacers are made in four common shapes, and the shape follows how the part is held, turned and loaded. Profab turns and mills these to your drawing in metric and inch sizes.

Round Spacers

A round spacer is a plain sleeve and the most common form. It holds a fixed gap around a bolt, stud or shaft and is made to the inside diameter, outside diameter and length you specify.

Hex Spacers

A hex spacer has flats on the outside, so a spanner can turn or hold it. Choose hex where the part must be tightened, locked or kept from turning against a neighboring part.

Stepped Spacers

A stepped spacer has two outside diameters. The smaller step locates in a hole while the larger one seats against the face, which positions the spacer and sets the gap at once.

Flanged Spacers

A flanged spacer has a wide rim at one end that spreads the load over a larger area and keeps the spacer from sliding into a slot or hole. It combines the jobs of a spacer and a washer.

ShapeFeatureChoose it when
RoundPlain sleeveA fixed gap round a fastener is all that is needed
HexFlats for a spannerThe part must be tightened or kept from turning
SteppedTwo outside diametersThe spacer must locate in a hole as well as set a gap
FlangedWide rim at one endThe load must spread or the spacer must not slip through

Standoffs: Female, Male and Mixed Ends

A standoff replaces a spacer and a through-bolt with one threaded part, though it still needs a screw or a tapped hole at each end. It holds a gap and fastens in the same piece, so it suits panels, boards and enclosures where the back of the part cannot be reached.

Female Standoffs

A female standoff has an internal thread at one or both ends and takes a screw from each side. It is the common form for holding two panels apart.

Male-Female Standoffs

A male-female standoff has a stud at one end and an internal thread at the other. It screws into one part and takes a screw from the other, so one side needs no nut.

Male Standoffs

A male standoff has a stud at each end and is fastened with nuts or screwed into tapped holes. Specify the thread size, the thread gender at each end and the body length.

Spacer, Standoff, Bushing, Washer, Shim and Collar

These parts are often ordered under the wrong name, so the job each one does is the safest way to tell them apart.

PartJobWhat to specify
SpacerHolds a gap round a boltInside diameter, outside diameter, length
StandoffHolds a gap and fastens without a through-boltThread size and gender, length
BushingGuides a sliding or turning shaftShaft and housing fit, lubrication
WasherSpreads load or makes a small height changeInside diameter, outside diameter, thickness
ShimAdjusts spacing in thin layersThickness
Shaft collarLocates or clamps on a shaftShaft diameter

Special Spacers for Rod Ends and Bearings

Two special spacers do more than set a gap. Misalignment spacers fit either side of a rod end ball to raise its swing angle and keep the ball centered on the bolt. Bearing and axle spacers set the distance between bearing races or across a wheel hub.

For the bearing and axle type, the length controls the whole bearing stack, so send the bearing model and the full stack length when you enquire. For misalignment spacers, the spacer bore, the bolt diameter and the spacer shape set how far the rod end tilts. The limit comes when the spacer, bolt or ball neck touches the housing, so check the angle for your rod end size.

Spacer Materials in Common Use

Spacers are made in a short list of materials, and the choice follows the environment, the weight, the electrical needs and the load. The material of the spacer should also be considered together with the fastener it sits around.

Plated and Plain Steel

Steel is strong and low in cost, and it is usually zinc-plated for dry, indoor assemblies. The plating is the main protection against rust, so steel spacers are a poor fit where the part is washed, splashed or left in salt air.

Stainless Steel

Stainless steel is the choice where corrosion resistance matters, such as marine equipment, washdown areas, outdoor machinery and food and medical equipment. It keeps its strength and its surface without a coating, and it is easier to clean than plated steel. Profab supplies stainless spacers in 304, 316L and 17-4PH: 304 for dry and mild service, 316L for chlorides, and 17-4PH for high load in non-chloride settings. The other materials in this chapter are listed for comparison.

Aluminum

Aluminum is light and non-magnetic, and it is usually lower in cost than stainless. It suits light assemblies and weight-sensitive designs, and it is softer than steel, so it deforms sooner under a high clamp load.

Brass

Brass is heavier and stiffer than aluminum, conducts electricity and resists corrosion in many settings. It is often plated, and it is common in electrical and electronic assemblies.

Nylon and Plastic

Nylon is the usual choice where full electrical insulation is needed, as in electronics. It is soft and takes little clamp load, it can creep and absorb moisture, and it is not suited to heat or heavy loads, so check the grade datasheet for the temperature limit.

Spacer and Fastener Pairing

Match the spacer to the fastener in a corrosive setting. Use stainless for the spacer and its bolt, because in a wet setting aluminum next to stainless can corrode, as it is the less noble metal, and brass with stainless is a milder pair. Thread galling is the failure to watch for on stainless standoffs, and same-grade threads gall most, so lubricate them.

Bore, Outside Diameter and Bolt Clearance

The bore of a spacer must pass the bolt without binding and without letting the spacer wander. The clearance hole sizes in ISO 273 give the usual starting point. Use the fine series for a closer fit on the bolt and the medium series for general work, and Profab confirms the bore against your drawing. These are clearance holes for loose bolts; a bearing or axle spacer is bored to the shaft fit instead.

Bolt size (ISO 273 reference values)Fine clearance boreMedium clearance bore
M33.2 mm3.4 mm
M44.3 mm4.5 mm
M55.3 mm5.5 mm
M66.4 mm6.6 mm
M88.4 mm9.0 mm
M1010.5 mm11.0 mm
M1213.0 mm13.5 mm

The outside diameter sets how much wall carries the load and how much face area the spacer offers the parts. Keep it about equal to the contact diameter of the washer or bolt head where space allows. The bearing area then sits on the spacer wall, and the head does not dig into the edge of the bore.

Length, End Faces and Tolerance Stack

Length is the dimension that most often causes trouble, because errors add up through a stack. Take a stack of four spacers on a drawing that allows plus or minus 0.05 mm each. In the worst case the stack can be off by 0.20 mm. If the errors are independent and centred, the root-sum-square estimate is about plus or minus 0.10 mm, found by multiplying one tolerance by the square root of the number of parts. The worst case is the safe figure for a critical fit.

Tighten the tolerance only where the stack needs it, since each step costs more to hold. Profab turns spacers to tolerances as tight as plus or minus 0.01 mm on critical dimensions, so a stack can be held as tight as the fit needs.

Surface Finish and Cleaning

The finish decides how the spacer behaves in a wet or hygienic setting. A machined stainless surface has no plating to wear off, cleaning and passivation can be added, and it suits most dry and general assemblies.

Food and medical equipment often specifies an electropolished surface, which is smoother and easier to wash. State the finish with the order.

Load, Compression and Galling

A spacer carries the clamp load of the bolt as compression through its wall, so a spacer that is too thin or too soft will crush or yield. The load depends on the bolt size and the torque, and a thicker wall or a harder material carries more.

Stainless parts add a second risk. Threads on stainless standoffs and bolts can gall, which locks them together while they are being tightened, so apply anti-seize or thread lubricant and tighten slowly. Profab does not publish load ratings for spacers, so send the bolt size, the torque and the environment with your enquiry.

Where Spacers Are Used

Spacers appear wherever a gap must be held exactly, and the material and the finish change with the setting.

Electronics and PCB Assemblies

M3 and M4 spacers and standoffs hold boards apart.

Automotive and Machinery

M8 and M10 spacers set gaps in drivetrain and chassis stacks, where a stack error shows up as play or binding.

Marine and Offshore

Standoffs and spacers create controlled clearances for enclosures and panels in salt spray, where a molybdenum-bearing stainless is the safer choice.

Food and Medical Equipment

Washdown equipment uses 316L, which resists many washdown cleaners better than 304, so check the chloride content and concentration of the cleaner against the grade.

Wheelchairs, Orchards and Turbines

Manual and powered wheelchairs use axle spacers to set bearing and wheel positions along the axle. Orchard machinery uses stainless spacers, 316L where the fertilizer contains chlorides, in wet, fertilized conditions, and hydropower equipment uses them in bearing stacks that run wet.

Measuring a Spacer for Replacement

A worn or missing spacer can be replaced from a measurement. Measure each dimension on the part, and measure the bore on the bolt it fits.

MeasureHowWhy it matters
Inside diameterCheck the bore with a pin gauge or calipersMust pass the bolt or shaft
Outside diameterMeasure the widest point of each stepSets the bearing area and the fit in any hole
LengthMeasure between the end facesSets the gap and the stack
End facesCheck they are flat and square to the boreKeeps the stack from tilting when it is clamped
Thread (standoffs)Check the type, size and genderMust seat on the mating part

Choosing a Profab Spacer

Work from the type to the bore, the faces, the length and the material, and confirm the result against the stack you are filling. Profab machines spacers to your drawing or sample, and standoffs need a thread size and gender while washers and shims need a thickness.

As a worked example, take a washed-down food line where four spacers set the gap between two plates on M8 bolts. The wet environment points to stainless, and the medium clearance bore for M8 is 9.0 mm. The length tolerance then follows the stack, as in the tolerance chapter above. The full range is on the stainless steel spacers page.

What to Send for a Spacer Quote

Send the drawing or a sketch with the diameters, the length and the tolerance, and the shape. Add the material, the environment and the quantity. For a replacement, a photo of the part with a ruler beside it and the measurements above are enough to start.

Conclusion

Choose a spacer by working through the type, the bore, the faces, the length and the material in that order, then check the tolerance of the stack. Send your drawing to Profab Machine and we will check the bore, the diameters and the length against it before we quote.