Get A Quote
Complete Clevis Guide

Clevis Guide: Types, Materials, Sizes and How to Choose

A practical guide to clevises and clevis joints: DIN 71752 and ISO 8140 sizes, fork and pin fit, clevis pin retention, threads, materials in common use and selection.

Engineering GuideClevis & Pinned LinkagesStainless Steel

Quick Answer: choose a clevis by working through five decisions in order. First pick the standard or the drawing it must match, then the pin diameter and fork width, then the thread on the shank, then how the pin is retained, and last the material. The load and the way it is applied then decide whether that size is strong enough.

DecisionOptionsStarting point
StandardDIN 71752, ISO 8140, custom drawingDIN 71752 for cylinder rods, ISO 8140 for 10 bar pneumatic cylinders, a drawing for anything else
Pin and forkPin diameter, fork width, single or double shearTake both from the mating eye
ThreadFemale or male, metric or inch, coarse or fine, right-hand or left-handMatch the rod or cylinder thread exactly
RetentionCotter pin, R-clip, circlip, snap ring, custom groove or cross-holeChoose by vibration exposure and by how often the joint is opened for service
MaterialZinc-plated steel, stainless steel, aluminumStainless where the joint is wet, washed or exposed for years

What Is a Clevis?

A clevis is a U-shaped forked body with two parallel ears and a thread on its shank. A pin passes through the holes in the ears and through the part you are connecting. This makes a pinned joint that pivots in one plane while it carries a pull or a push along the link.

The clevis and the clevis pin are two separate parts, and orders go wrong when the two are confused. The clevis is the fork with the thread, and the pin is the plain cylinder that holds it to the mating eye. Many names cover the same fork: rod clevis, yoke end, fork end, fork head and clevis rod end.

How a Clevis Joint Works

A clevis joint works by sharing the load between two ears. The mating eye or tongue sits between them, and the pin runs through all three, so the pin is loaded across two cross-sections at once. This arrangement is called double shear, and it is the standard way a clevis is used.

When only one ear carries the load, the pin is loaded across a single cross-section, which is single shear. All else equal, the same pin carries about half as much in single shear as in double shear. A single-shear joint therefore needs a larger pin or a lighter load, and bending of the pin is checked separately.

The joint turns freely on the pin but has no built-in allowance for misalignment, which is the main difference from a rod end. The link swings in one plane, and a mating part that is out of line loads one ear of the fork.

The thread on the shank joins the clevis to the rod, the tie bar or the cylinder rod. Because the thread sets how far the clevis sits on the rod, it is also how a link gets its length.

Clevis Types and What Each Is For

Clevises are grouped by the job they do, and Profab makes four of them. The shape of the fork is similar, so the difference is the thread, the standard and the duty the clevis is built for.

Clevis Rod End: General Purpose

The general-purpose clevis has a threaded shank that screws onto a rod or tie bar and a pin bore for a standard clevis pin. The fork width and the bore are cut to the drawing.

Steering Clevis: Double Shear

A steering clevis fits drag links and tie rods where the pin runs in double shear. Its fork width is matched to the thickness of the steering arm, and a high-strength material can be chosen for shock loads.

Clevis Joint: Pinned Linkage

A clevis joint is the plain pinned connection for linkages, tension rods and actuators. It pairs with a clevis pin, and a left-hand thread makes a turnbuckle-style assembly.

Threaded Clevis: Cylinder Rods

A threaded clevis has a female thread for hydraulic and pneumatic cylinder rods. Fine-pitch and left-hand threads are cut on request, to the DIN 71752 designation or to your drawing.

TypeThreadTypical use
Clevis rod endThreaded shank onto a rod or tie barGeneral linkages
Steering clevisShank matched to the drag link or tie rodSteering linkages in double shear
Clevis jointRight-hand or left-handLinkages, tension rods, actuators
Threaded clevisFemale, fine pitch on requestHydraulic and pneumatic cylinder rods

DIN 71752 and ISO 8140

DIN 71752 is the German standard for rod clevises used on cylinder rods. Its sizes are named by the inside width of the fork, which equals the pin diameter, and by the slot length. A G10x20 clevis therefore takes a 10 mm pin in a slot 20 mm long. Profab lists sizes from G4x8 to G50x100, with fine-pitch FG variants. Some of these are maker sizes that are not in DIN 71752. Pin bores and threads are cut to the standard or your drawing, for example an H9 bore and a 6H thread.

ISO 8140 gives the interchangeable mounting dimensions for clevises on 10 bar pneumatic cylinders, and these clevises are commonly sold as interchangeable with CETOP RP102P equipment. When you buy for a cylinder, give the cylinder model, because the cylinder decides which standard applies and which thread pitch and slot the clevis needs.

DIN designationPin diameterSlot length
G6x126 mm12 mm
G8x168 mm16 mm
G12x2412 mm24 mm
G16x3216 mm32 mm
G10x2010 mm20 mm

These rows show how the designation reads; the slot length is the depth of the slot in the fork. Sizes above these, such as a 20 mm pin, are maker sizes that DIN 71752 itself does not list. The thread, the overall length and the larger sizes vary by size and by maker, so confirm the exact dimensions against the standard or the cylinder before you order.

Clevis Pins and How They Are Retained

The pin holds the joint together, so it is chosen as carefully as the clevis. It must match the bore of the clevis and the mating part, and it must be held in place against vibration and against the joint being pulled apart in service.

RetentionHow it worksChoose it when
Cotter (split) pinPasses through a cross-hole near the end of the pinVibration exposure matters more than quick servicing
R-clipSprings through the cross-hole and clips round the pinThe joint is opened often for service
Circlip or snap ringSeats in a groove cut near the end of the pinA compact, low-profile retention is needed
Custom cross-hole or grooveCut to a drawingThe standard pin does not fit the assembly

A pin with a head at one end and a cross-hole at the other is the most common form. Profab supplies the clevis with matched pins as a set, plain or with custom retention grooves or holes cut to match your assembly.

Thread, Hand and Length Adjustment

The thread on the shank must match the rod or cylinder it screws onto in every respect: internal or external, metric or inch, coarse or fine, and right-hand or left-hand. A coarse thread on a fine-pitch rod will not seat, and a joint forced onto the wrong pitch damages both parts.

A clevis with a left-hand thread on one end of a link and a right-hand clevis on the other makes a turnbuckle. Turning the rod or body between them shortens or lengthens the link without taking the pins out, and a jam nut on each end locks the length. Profab cuts the thread to match your rod or cylinder, so no adapter fitting is needed.

Clevis Materials in Common Use

Clevises are made in a short list of materials, and the choice follows the environment and the load more than any data sheet. The body and the pin should also be considered together, because a pin that corrodes or wears stops the joint before the clevis does.

Zinc-Plated and Alloy Steel

Zinc-plated steel is the common choice for dry, indoor and short-life linkages. It carries high load at low cost, and the plating is the main protection against corrosion. Where the pin turns, the plating wears away first, and the bare steel then rusts at the pin bore.

Stainless Steel

Stainless steel suits wet, washed and outdoor service. The whole part resists corrosion, so there is no thin layer to chip or wear away at the pin bore under repeated double-shear movement. Profab machines clevises in 304, 316L and 17-4PH. Which stainless to use follows the chlorides in the environment and the load: 316L for salt spray and chloride sanitisers, 17-4PH where strength is the limit. Profab confirms the grade against the drawing when it quotes.

Aluminum and Light Alloys

Aluminum clevises exist for light pneumatic work where weight matters and the load is low. Profab clevises are stainless, and aluminum is not the first choice for chloride washdown or high load.

Pin and Body Pairing

Use a pin and a body from the same material family in a corrosive setting. Mixing a plain steel pin into a stainless clevis can promote corrosion of the steel pin in wet service, and Profab supplies matched pins so the pair behaves alike.

Load, Shear and Hidden Loads on a Clevis

A clevis is sized for the pull along the link, but it usually fails from loads the pull calculation leaves out. The pin bends between the ears, the fork spreads under shock, and a bracket that is not square to the link adds a sideways load on one ear.

The fork width must follow the real width of the mating eye. A fork that is wider than the eye lets the part slide and rattle, and one that is narrower cannot be assembled without forcing. For a DIN size the width is fixed by the designation, so check the eye against it, and on a drawing specify the width to the actual eye.

Profab does not publish load ratings. Send the load direction, how often it reverses, whether the joint takes shock, and the pin diameter with your enquiry, and the load case is confirmed at quotation.

Environment, Washdown and Surface Finish

The environment decides the material and the finish. Stainless clevises ship bright machined as standard, which is a clean machined surface free of scale and plating and ready for dry indoor automation and general industrial assemblies.

  • Passivation: a chemical passivation to ASTM A967 restores the protective surface layer and removes free iron left by machining, which supports corrosion resistance in marine and chemical exposure.
  • Electropolishing: removes surface peaks to leave a smoother, easier-to-clean surface for food, pharmaceutical and CIP washdown linkages.
  • Mirror polishing: a reflective finish for parts that stay in view.

Surface finish is specified when the order is placed. In a washdown area, also look at the pin and the retainer, because the smallest part in the joint is often the one that corrodes first.

Where Clevises Are Used

Clevises appear wherever a pinned connection carries a pull or a push through a link. The material and the standard change with the setting.

Hydraulics and Pneumatics

Cylinder rods thread into clevises, with fine-pitch threads where the rod calls for them. The cylinder model usually decides the size.

Marine and Rigging

Standing rigging and deck hardware clevises meet salt spray all season. A solid stainless fork has no plating to lose in that exposure.

Agriculture

Harvester and plough linkages meet fertilizer spray all season, and stainless hardware keeps working where plated parts corrode.

Architecture and Facades

Point-fixed glazing and cable railing terminals use bright-machined or mirror-polished clevises, which stay clean where rust bleed would stain the glass.

Clevis, Rod End, Shackle and Ball Joint

A clevis, a rod end, a shackle and a ball joint all connect a link, and each does it a different way. A clevis pivots in one plane on a pin, and a rod end tilts on a ball held by a bolt. A shackle closes a loop with a pin for lifting and rigging, and a ball joint snaps a ball into a socket.

PartMotionTypical use
ClevisOne plane, pinned, double shearCylinder rods, linkages, tension rods
Rod endTilts and swings, bolt through the ballLinkages with misalignment
ShackleClosed loop with a pinLifting, rigging, mooring
Ball jointTilts, typically a snap-in socketCompact control linkages

Choose a clevis when the mating parts line up in one plane and the pin can be loaded in double shear. When the parts can sit out of line, a stainless steel rod end tolerates the misalignment that would load a clevis fork unevenly.

For small control linkages that need a snap-in connection, see the ball joints guide.

Measuring a Clevis for Replacement

A worn clevis can be replaced from a measurement, and these are the dimensions to take. Measure them on the part and write them on the drawing or the photo.

MeasureHowWhy it matters
Pin diameterMeasure the pin or the bore with calipersSets the DIN size and the fit
Fork widthMeasure the gap between the inside faces of the earsMust match the width of the mating eye
Slot lengthMeasure from the fork tip to the bottom of the slotCompletes the DIN designation
ThreadCheck the type, the pitch, and the hand with a thread gaugeMust seat on the rod without force
Overall lengthMeasure from the pin center to the end of the shankSets the length of the link

Choosing a Profab Clevis

As a worked example, take a washed-down pneumatic cylinder whose rod has a metric fine-pitch thread. The cylinder model gives the standard and the size, the thread is read off the rod, and the wet environment points to stainless with a matched stainless pin held by a circlip. Profab checks the mating dimensions from the cylinder model or the existing part before the order, and the stainless steel clevis page lists the full range.

What to Send for a Clevis Quote

Send the drawing or a sketch with the standard or the cylinder model and the measurements from the table above. Add the retention you want, the material, the environment and the load. For a replacement, a photo of the worn clevis with a ruler beside it is enough to start.

Conclusion

Choose a clevis by working through the standard, the pin and fork, the thread, the retention and the material in that order, then confirm the load and the way it is applied. Send your drawing to Profab Machine and we will check the fork, the bore and the thread against it before we quote.