
Custom weld-in bungs in 304, 316L, and 17-4PH, with other grades on request. Threaded tube adapters that give a tube end the internal thread of a rod end, left or right hand, made to your tube outside diameter and wall, to your drawing or sample.
Applications: Fabricated Suspension Links, Steering and Tie Rods, Hydraulic and Pneumatic Cylinder Linkages, Agricultural Machinery.
A bung is made to the tube it is welded into, so the tube outside diameter and wall decide the bore left for the bung. These combinations are common on rod end link kits. Any tube and thread is made to your drawing. Tube ID is the outside diameter less two walls. Left and right hand bungs, shoulder, and length are set on your drawing.
| Tube OD | Wall | Tube ID | Bung Thread |
|---|---|---|---|
| 1.000 in | 0.095 in | 0.810 in | 1/2-20 |
| 1.000 in | 0.120 in | 0.760 in | 1/2-20 |
| 1.250 in | 0.095 in | 1.060 in | 5/8-18 |
| 1.250 in | 0.120 in | 1.010 in | 5/8-18 |
| 1.500 in | 0.120 in | 1.260 in | 3/4-16 |
| 1.500 in | 0.250 in | 1.000 in | 3/4-16 |
Order bungs for the tube wall you will use, because the same outside diameter in a thicker wall leaves a smaller bore for the bung.
| Form | Shape | Typical Use |
|---|---|---|
| Stepped bung | A smaller body enters the tube and a shoulder stops on the tube end | Links where the bung must seat the same depth every time |
| Straight bung | A plain round body, no shoulder | Tubes where the bung sits inside the tube, flush or recessed |
| Weld-prep chamfer | A bevel on the outer edge of the shoulder | Gives the fillet weld a groove to fill |
| Left and right hand set | One bung of each hand | Links that adjust length by turning the tube |
| Custom bung | Thread, outside diameter, bore, and length to drawing | Tubes and rod ends that a standard bung does not fit |
Send a drawing, a DXF file, or a sample. Our engineers review the dimensions and the tolerance before cutting metal, and we CNC machine the part ourselves, so you deal directly with the factory.
We turn each bung to your tube outside diameter and wall, with the thread cut on the same part, so the body seats square and the thread runs true.
Tube material, salt, moisture, and washdown chemicals drive the choice between 304, 316L, and 17-4PH. We confirm the grade against your drawing before production, and tiered pricing is available on larger orders.












A weld-in bung is a short threaded plug welded into the end of a tube so the tube can take a rod end. It is also called a tube adapter or a threaded tube insert.
Match the thread of the rod end shank and the hand, then choose the bung for the tube outside diameter and wall. The same outside diameter in a different wall needs a different bung.
It is better not to. Weld heat and spatter can damage the thread or the rod end, so weld the bung in empty and run a tap through the thread afterward.
Choose 316L where the bung sees salt, chlorides, or chloride-based cleaning chemicals, because it resists pitting better than 304. Choose 304 for indoor, dry, or mildly humid service, where it costs less.
A quote request needs the thread size and hand, the tube outside diameter and wall, whether a shoulder is needed, the length, the grade, and the quantity. A drawing or a sample speeds it up.
If you already have drawings, email them to [email protected].
[email protected] ↗We use cookies to run this site, to measure how it is used, and to show relevant ads. You can accept all, reject all non-essential cookies, or choose by category. Privacy Policy